Hello 

Has anyone purchased an exhaust system from Circuit Works in Texas?

Need to know how they fit / and quality of system...do the tips stick out to far

basically the appearance of the exhaust

If you have pics....that would help

thanks

jwild

Original Post

The Circuit Works exhaust and the PPC exhaust may be one and the same. They certainly look identical. Circuit Works would probably tell you if you asked. 

Somebody should try them, and give us a report, rather than just pointing out potential problems!

They do have wide tube pipes, and are supposed to be SS, although you could run into issues adapting a 2 1/2" pipe to the stock header collectors, but if you have the Hall Pipes - that might be a good thing...

You might want to change the collectors & tailpipe to a flange clamp.

 

(OOPS - There I go, pointing out potential problems!)

 

ONE WOULD THINK....  That they built a jig from a stock Ansa system, and can bend a tailpipe to match the original curves & dimensions...

 

I can't find my pictures of my tailpipe fabrication, but that's what we did.

 

06-16-2014 [5) (Medium)06-17-2014 [1) (Medium)

 

Attachments

Images (2)
@rocky posted:

Somebody should try them, and give us a report, rather than just pointing out potential problems! 

There's an irony in that, feel free to contribute to the cause....

I'd like to know about Circuit Werks too.  I see they are selling on eBay regularly.  I've not seen any photos of them installed or seen a post by anybody with first hand experience.  The referenced links in this forum are pretty dated too.

That is what I am trying to figure out.....I did talk with them....they make the whole thing..including the mufflers...nice thing it is all SS.....the only question I had after talking with them......header flange....it whole thing they told me was it is style after a GTS....I was going to scan a picture to them on my flange dimensions

thanks

jwild

Get them to send a sound clip of how it sounds at varying, stainless can sound pretty tinny in an exhaust note depending on thickness used and resonate more at the infamous 2000-2200 rpm.

I have the circuit werks exhaust. bought one of the first sets in late 2017.  nice quality, good sound, tips seem to have the right "rake" and extension length from the body.  the flanges are ok, but you will need to elongate the holes to get a little more horizontal adjustment of the tips when looking from behind. I plan to cut the flanges off my headers and the exhaust and weld on ball sockets which allow more adjustment very easily

Attachments

Images (1)

It looks great. Is the muffler tubing 2-1/4” like the Euro GTS system or 2-1/2”? Rather than ball sockets I’d recommend V-Band clamps. 

been a while but I think 2.5" - call them, they are in texas and are very helpful. vband clamps are great too but i think you'd get more "total" adjustment with the ball flanges, no?

Thanks for the great response....I have talk with them they were very open....and honest on the flange type and what I might have to do to make them fix...I donot have the stock headers any more.

The pictures show me exactly what they look like....When talking with them , they did tell me they had sold about 20 sets....The two things I would change would be the length  of the tips(make a little shorter...my choice and maybe angle a little different) and the suggestion to ball or Vclamps...I would like to be able to adjust at some point....plus I am adding Fuel Injection...so O2 bungs will need to be added

I will call again tomorrow to see what can be done. Will update everyone on the feedback.....Again many thanks for the pics...they tell all....also minor adjustment would be great...notice on the picture looks like left could be tweek a little...but that is me being picky   lololol

Again they told me they copied the GTS...did not say if it was the Euro GTS system

Thanks

jwild

Add Reply

Post
×
×
×
×
Link copied to your clipboard.
×