Replies sorted oldest to newest
I have the same early switch, but there is a sheared off plug next to which is the number 30 embossed in the black plastic housing. Does anyone know where that plug is supposed to go to?
"30" is a DIN number that essentially means "battery"...This is the connection to the 12v source that is then switched for whatever.
@doobwaa posted:Does anyone know what the single plug is for on the Turn Signal Switch Wiring ( white wire w/ blue stripe )
Photo in attachment
It was connected to a solid purple wire in the main harness under the dash
Bought a replacement switch and it does not have this extra connection
Any help would be appreciated - Thank you
That extra wire is for the drivers lights on GTS , GT5-S and GT5 Pantera's
those cars have extra drivers lights., GTS have them mounted under the front bumpers, GT5-S and GT5 into the front spoiler.
you can give a flash while the headlights are off
while the early Pantera and the new replacemenmts switches dont have this function , the GTS, GT5-S and GT5 has this extra function, pulling into the backward is possible, by the early Pantera's and the later replacements it's not.
Simon
A couple of years ago, I purchased a new reproduction turn signal switch from the capri vendor teamblitz. It does incorporate the terminals necessary for the flash to pass function.
I am using that function to control two LED driving lights I installed in redesigned turn signal pods.
Larry
So in other words, on car #2034 I don’t need to worry that this terminal is not attached to any leads?
@lf-tp2511 posted:A couple of years ago, I purchased a new reproduction turn signal switch from the capri vendor teamblitz. It does incorporate the terminals necessary for the flash to pass function.
I am using that function to control two LED driving lights I installed in redesigned turn signal pods.
Larry
Larry,
that looks very good , wher have you purchase that front spoiler ?
I was looking for 1 or 2 .
regards
Simon
@hej posted:So in other words, on car #2034 I don’t need to worry that this terminal is not attached to any leads?
yes , I think so , if everything is works as suspect , it dont have a function.but sometimes they switch colors on the replacement switches, easy to find out whit the old switch in hand .
you can chance the pins from the connector..
Simon
Simon, if I’m not mistaken, Larry’s front spoiler is from Pantera Performance in Colorado. I believe it’s made from urethane or some other type of flexible material.
Yes, spoiler is from Dennis. It is made of ABS black plastic with a pebble finish. He also offers it in fiberglass.
cost a few years ago was $125. I do not know if he currently has them in stock.
Larry
I’m calling him shortly. I’ll find out if they’re in stock and report back.
Another figment question. Reinstalling the turn signal / blinker stalk. Located correctly on the column (shroud holes all match up), but the cam fitting on the steering wheel hub (quick release version) comes no where near deep enough on the splines to engage the cancellation tab on the stalk. 
@hej posted:Another figment question. Reinstalling the turn signal / blinker stalk. Located correctly on the column (shroud holes all match up), but the cam fitting on the steering wheel hub (quick release version) comes no where near deep enough on the splines to engage the cancellation tab on the stalk.
You need a Cam turn signal canceling Part nr. 03006A Wilkinson .
original they are red.
Simon
@lf-tp2511 posted:Yes, spoiler is from Dennis. It is made of ABS black plastic with a pebble finish. He also offers it in fiberglass.
cost a few years ago was $125. I do not know if he currently has them in stock.
Larry
Some time ago I ask Adam Quella, they had them not in stock.
Simon
Dennis does not have the ABS spoiler in stock. Adam told me several months ago their vendor "lost" their mold for it and screwed them. Adam was trying to figure out where to go from there. I have not asked him lately.
Regarding the red cam extender, found it. Multiple years of varying states of disassembly will scatter stuff about. Thanks again.
What is this tab on the ignition switch supposed to be attached to?
Can be massa/ground , but not used .
Simon
