Anyone need glass, trim or gaskets?

(The blacked-out side windows are sold)

Rear window would be best for local (AZ or SoCal) delivery...

was looking for a driver side rear quarter grill , the closed early one.

Simon

How much for the 1/4 window gaskets? Any cuts?

Hey guys….

Simon - sorry…. I think I have only right side gills, but maybe for a Euro car, that’s what you are looking for?  Let me know.

Husker - sorry, I only have the frames.  But if the gasket is the same profile as the windshield gasket I have a 10’ length of that in good condition…

Rocky

Rocky , I was looking for a driver side early car not a Euro car

Some misc. small parts...  PM me if you're interested...

Handbrake pads (2 sets), have the tab on the back, but may need the guide holes expanded.  1 set is new, 1 set nearly new.

Stock Proportioning Valve and (SOLD) Brake Fluid Distribution Block.  Needs gutted (or rebuilt - articles on "how-to" online).  No brake light switch or fluid pressure variance switch on distribution block.  From 5357.

Stock Proportioning Valve.  Needs gutted (or rebuilt).  From a '72...  I think 4280.

(SOLD) Stock Pantera Water Pump Pulley.  From 5357 - single groove.

Rocky

I’m in need of rear glass and weather stripping if you have it. I’m told I need the larger glass pre 2000

PM sent to 1770…

This seems to be the best thread that I can find about the rear window differences…

https://pantera.infopop.cc/top...-pushbutton-panteras

Rocky

Thanks for the thread link. Seems my path is to find the proper seal then it’ll lead me to the correct glass or have one cut.

Just for posterity, here’s the measurements of the window that I have….

Height (Center):  11 1/8”

Height (Tip->Top): 14 3/16”

Width (Tip->Tip): 58 7/16”

Thickness: .315”

It’s safety glass with a layer of ? between two sheets of glass.

Rocky

Thank you for the measurements. My car is in a trailer so getting in a position to properly measure it is not possible so



== To reply by email, write above this line. ==

New Reply By rocky

Rocky's Big Batch of Pantera Parts FS.... Reply by rocky Just for posterity, here’s the measurements of the window that I have…. Height (Center):  11 1/8” Height (Tip->Top): 14 3/16” Width (Tip->Tip): 58 7/16” Thickness: .315” It’s safety glass with a layer of ? between two sheets of glass. Rocky This post contains 3 images. [ View Reply ]

The De Tomaso Forums You received this based on your notification settings. You can adjust your settings or unsubscribe anytime.

Got a pair of really nice 8" Campis - freshly painted over a Zinc Chromate primer base - Painted in the correct Argent Silver (Thanks, RickP!)

Comes complete with brass Isis Centers (not the modern cheapy aluminum ones), retaining clips and metal valve stems.

Really nice wheels, a great upgrade if you are still running the stock 7" wheels up front.

PM me with your email and I'll send lots of pictures, both before and after paint.

$1100, offers considered - Free pickup in Tucson, Free transport to Phoenix (if you're not in a rush), other than that, buyer pays shipping.

Rocky

Also can provide a pair of nice Goodyear Arrivas to match the wheels ($50 each, with wheel purchase!)

Better Pictures of my Seat Rails.  These will need cleaned up, and lubed.

There's a recent thread about making rollers - these ones will need them, as one pair of rails has two (each) of the old rubberized rollers, and one pair of rails doesn't have rollers installed (from what I can see).

All parts are complete, (except for the rollers, described above) with 4 tracks, 8 Allen-head mounting cap screws, (2) knobs, (3) wire handles to release the seats, all springs and catches.

Perfect for that Corvette C4 Seat retrofit project you've been considering!