Added bits on 2/18 and 2/21. Thanks for looking!
OK, finally got around to a USED (mostly unless otherwise stated!) list of bits and pieces I collected from various.......
As always, first come first served.
$35 Alternator Adjusting Bracket for center mount Alt.
$25 Carello Tail lamp wiring rubber boot- nice used!
$75 RH Tail lens, NOS or good used….out of box.
$10 25mm defroster hose, NEW, for mid production cars, 20” long enuf for one side, can’t find this in US.. (30mm used other side)
$25 Brake/Clutch Fluid Reservoir- original style with copper tubing stub on outlet, with cap.
SOLD Veglia clock face (white letters) “Elettronico” and two pieces of clear plastic for making new lens.
SOLD Box of wheel studs 2- NEW late fronts, 2- NEW late rear, two early rear-used- 4 NEW Dorman 610-312 front? Early???
$ Hatch/hood release handles (2)
$35 Door jamb guide chrome pieces (2) with one rubber, screws Rechrome for best looks.
SOLD New Ignition Switch- Repop from ???? I wouldn’t……
$75 Used Ignition Switch/Black Bezel and “FIAT” key- action feels good, be sure to mount upside down!
$3 8 Dash lamps 3W #1815
$35 Shock absorber adapters for QA1 “Chrome” shocks- Custom machined. 8 pieces to do two shocks.
$25 Shock absorber adapters for QA1 Proma Star shocks- Custom machined. 2 pieces to do one shock.
SOLD Two used factory shock bushings, center displaced but would work for trans cross member still.
SOLD Wire junction blocks, 1 each- small wire-medium-large Multiple wire numbers accepted, like style used for headlamp/horn/tail lamp junctions.
SOLD Lucas “parts switches 1-31780 for parts, 1- 334870B (fan switch originally)
SOLD Green Brake Fluid hose- reservoirs to copper tubes and cylinders- NEW
$20 Box of Cable- 2 sizes NEW- hatch style latches (smaller) and e-brake cable (larger). 3mm & 1mm
$200 TWO- Good LH door latch mechanisms and handle support posts.
SOLD Lower engine block plate-cut off at engine block- allows about .100” more ZF input shaft engagement.
$10 Insulation pad- original engine compartment “flip up” section.
$75 Headers- new but need rework at flange to pipe areas- I think these may be first gen Hall Goose attempt…… tubes interfere with studs or bolt installation. Do not look like originals…more conventional.
$50 Mid production brake balance valve- I believe Bonaldi- locked up. Mounts to RH rear frame rail about engine area.
SOLD 23MM brake master cylinder “guts”. Seal holders and springs- Likely from late car or early Pantera.
$120 PAIR- 1” Small Block Ford valve cover extensions, for clearing roller rockers if needed. NEW
ZF parts- Input shaft/throw out bearing holder retaining bolts, Input Shaft seal for pilot bearing -1 only piece, Selector shaft seal (shifter).
Windshield Washer bottle and pump assy by Lucas. Scarfy from living in exhaust rich environment! Pump motor actually still works!
Smog Pump from mid 900’s car. Entire assy, pump, pulley, regulator valve and holding bracket, air hose to connect prior two items together, and special Goose mounting and adjusting bracket and bolts. These parts other than Goose bracket are same as GT350 manual trans car and this affects pricing.
$60 Radiator metal tubes (two curved front pieces)- reproductions. New.
2/21 NEW ADDS
$25 PAIR of used rear flip up hatch latches. These pop rivet to the engine compartment sidewalls and hold the flip up portion by the window in place. Clips are intact.
$15 Reproduction "spark plug wire holder". This is a piece that keeps your wires from rubbing on the jackshaft. I found that this didn't work on at least Edelbrock intakes as they have no extra holes by the T-stat housing area. I put a piece of heat shrink on it, but never shrunk it in place since I couldn't use it. But this will fit the stock Ford intakes just fine.
Parts of Unusual Status…..
Box of used parts….. half shaft bolts, ball joint bolts, hose clamps, ny-lock nuts from various parts, ZF nuts, used U-Joint clips
LH (2) and RH tail lamp lens- were NOS until the earthquake dumped them off of my shelf…….good for display, lower rear corners chipped, most have the pieces in the packaging still.
Box of misc window guide/channel felts- materials and doorframe outer rubber pieces. I’d call these samples…..
Ford Taurus/Sable various water hoses- I used 90 degree pieces (3/8”???) to connect to heater core on the RH side of dash where AC unit smashed up against heater core outlet……these are used and of various sizes and shapes!
Two front used ball joints- multi layer type.
One AC condenser fan blade- one blade busted off- rebalanced unprofessionally with nut and bolt…….
SOLD 3- Used CLUTCH Master Cylinder kit (SP1995)- has good Dust Cover seals (over pushrod)