Replicating a Mangusta Air Cleaner

Air intake hoses are 80mm, Steve L. had some (in original paper) for sale. Only paper really looks right. 

 If you want to go really far, I believe the vacuum motor on the air cleaner is a Ford 1968 part ( C8AZ-9D612-A)-- Lee

thanks for your response. Do the hoses attach directly to the 3” hole in the rear side panels or is there a 90 degree fitting that is attached to the side panel?  I have seen photos both ways.  How can I make contact with Steve L about purchasing the hose?

 Thanks 

Steve L goes by the handle "mangusta" on this forum.  See this thread for info about the hoses.

https://pantera.infopop.cc/top...217#1598208435649217

Brian, hopefully someone can help you out with measurements of the air cleaner (sorry, I am months away from my car and disappointed also that I don't have pictures already! Here are some pictures of the air cleaner, the air filter is a Napa Gold 2063---a cross reference shows it used on just about every Ford since the late 50's (including all Mustang, so starting with a low-profile air cleaner for a Mustang may not be a had start).   The air tubes turn 90' and go thru the cast aluminum piece on either side--there is no clamp at the air cleaner, at the "aluminum" end the tubes just slip fit to the insides.  These pictures of the hangers may help  https://pantera.infopop.cc/top...r-paper-tube-hangers

(hmm, if someone would make a paper template of the air horns and scan it...)

Lee

That is very helpful.  I will take some pictures and post them when I get done so you can all see how a farmer does it!  Thanks 

Lee, that's an interesting point about the filter being used since the 50s.....and (for better or worse) opens up a number of possibilities to where the basic air cleaner body came from.  It would be GREAT to identify the actual host used by DeTomaso since adding snorkels would not be a big deal.

Two identifying features come to mind. First is the Goose unit's OD, which from Steve's link below, must be about 19".  This seems to be 1 - 2" larger than a lot of normal Ford air cleaners, at least from the late 60s.

https://pantera.infopop.cc/top...-version-on-your-car 

Second feature is the protruding inner 'ring' or 'bead' stamped into the air cleaner cover, maybe 6 or 7" in diameter.  I don't see this type of ring when Googling Ford air cleaner images.  All covers have stamped features of some kind but as far as I've seen, nothing to match what's on a stock Goose.  My search has been FAR from exhaustive, but I would think at least 1 image would have popped up by now that showed a similar stiffening ring/bead.

So maybe we are dealing with an unconventional unit?  (e.g., Ford marine or military part, (if such things exist?). Leftover bits from some 50s Lincoln?  1961 school busses? Econoline Milk Trucks? ….. I've always assumed it's a Ford part, designed to work with Autolite carbs...but trying to think out of the box at this point

Guys,     The stock filter is a Ford staple item....used on early 60's Birds, then 1967 GT 390......then in Mustang/Cougar/Fairlane/Galaxie 68-70 427/428 ram air units, and some "regular" air cleaners.  (390's in 68 got a larger unit for some odd reason but used the smaller 428 style in 69....)

FA325 Fram comes to mind....but the mind could be off.....  I have one on the shelf....but shelf is 50 miles north....!

Just look for a 1969/1970 428CJ Mustang/Cougar/Fairlane (not 429!) and you'll get the proper filter element!

The stock base is a hand fab unit that DeT made to facilitate this element.  It is not a "drop" style base by any stretch of the term.  Basically the air cleaner actually lifts the base off the car by a little bit.

When I made my air cleaner out of the 68/69 truck (and MANY others) air cleaner base, it incorporated the stock drop.....and helped me clear the shields due to my use of the Edelbrock RPM intake....which is about an inch taller than a stocker.......   I did need to "raise" the clearance on the lid, around the area where the air cleaner bolt comes thru.....

Cheers!

Hey Steve,

Can you post a link to the thread where you documented making your air cleaner?  I looked for it but wasn't successful finding it.  It might be helpful to Brian.

Hi Garth, I was thinking it was the one linked above, might have been more than one however?  Regards Nate

Nate's original link went to the paper tubes in the for sale section!

I located the original post and forwarded the link to Brian already.   I had already sent him the pictures last nite!

The pictures are gone due to Comcast abandoning it's customers with "no more picture hosting"........ so some day when I can get a low cost internet connection with some bandwidth...... I can upload all the pictures again......  It's nice being out in the weeds, but I REALLY REALLY miss "high speed internet".......presently have "slow or no, pay as you go" internet......   disgusting.....   had to drop Netflix streaming...... cost upwards of $20 more a month extra  if you streamed one movie!  ....cuz you exceeded your limit.     I'd consider paying more, but can't find the info on the ATT website.....it is sooooo polluted with wireless phone crap......vs wireless internet NOT on your phone!!!!

Sorry for the rant.....the wound is still bleeding......!

I purchased my car with an aftermarket chrome top air clear a-la-Shelby. I have searched for many years to acquire the correct Mangusta assembly without success. I was lucky to have an owner lend me his. I have been working with a few specialized trades to make a reproduction air cleaner. I had asked a well known metal fabricator to make the inlet funnel but unfortunately it did not meet my expectation. The only way to accurately make was to have the unit 3D scanned.  From this I had a machinist make a Tool and Die mold made.

I purchased a sheet of 18 gage body sheet metal and along with a friend, cut-up squares and we stamped half funnels with his 10 ton press gave them a flange and spot welded the halves together as were the originals.

Concurrently the scan was used to have a metal spinner make a wood mould and spin a few center bowls. A wood buck has a short life but then it has a major cost saving compared to its steel equivalent.

Next step was to properly and accurately mate the funnels to the bases.

Reproduction piece welding completed complete with PCV inlet tube and vent tube hook.

Well Done. Exceptional exercise.  Thanks for sharing.

JT

Next came the task of painting the air cleaners.  I was sure we could use wrinkle paint in a can and play with temperatures to match the original mottled finish, but it was not to be that simple. After many attempts it was decided to try and find rare bulk product and then expand the methods and procedures. it took a professional painter a week to find a formula very close to the original large grain texture.

Finally out of paint shop old original vs new

This is the final kit complete with tubes, brackets and hardware